Regulatory trackerCoverage and methodology

Regulatory change tracker

Selected exposure-limit, industrial-hygiene and standards changes across the U.S., Canada and Australia, with source evidence and practical context.

Research checked throughNovember 11, 2026U.S. and Canada. Australia checked through September 17, 2026.View scope and remaining gaps

All findings

74 records
Federal: MSHAProposed

MSHA proposes revisions to the stayed 2024 silica rule

The U.S. Mine Safety and Health Administration proposed changes to the stayed 2024 silica rule, with a Federal Register publication date of November 12, 2026. The proposal would change how often operators sample, apply a 21 percent error factor before finding an exceedance, adopt OSHA's respiratory protection standard and revise medical surveillance, while keeping the 50 µg/m³ PEL and 25 µg/m³ action level.

Respirable crystalline silica5 sources · Checked Nov 18, 2026
QuebecProposed

Quebec proposes a replacement RSST Schedule I exposure-limit table

Quebec's CNESST published a draft regulation on November 11, 2026 that would replace the whole exposure-limit table in Schedule I of the RSST. Proposed decreases include benzene from 0.5 to 0.2 ppm, xylene from 100 to 20 ppm, hardwood dust to 1 mg/m³ and titanium dioxide to 3 mg/m³ respirable; quartz and cristobalite stay at 0.05 mg/m³ respirable.

Air-contaminant limits and notations2 sources · Checked Nov 18, 2026
Federal: EPA TSCAVacated

Methylene chloride laboratory deadlines no longer apply after court vacatur

EPA extended non-federal laboratory methylene chloride deadlines by 18 months in 2025. The Fifth Circuit vacated the underlying 2024 rule on September 15, 2026, so the laboratory dates, including the November 9, 2026 monitoring date, no longer apply.

Methylene chloride4 sources · Checked Nov 18, 2026
CaliforniaDraft

California discusses prohibition on high-silica artificial stone

Cal/OSHA posted an updated discussion draft on October 22, 2026 for an emergency rule banning the manufacture and fabrication of artificial stone slabs or panels containing 1.0% or more crystalline silica. The draft adds an installation ban 360 days after the rule's effective date and an artificial stone action level of 10 µg/m³ as an 8-hour TWA.

Artificial stone / silica4 sources · Checked Nov 18, 2026
New MexicoProposed

New Mexico heat illness rule hearing moved to March 22, 2027

New Mexico's proposed heat illness rule has not been adopted. On August 28, 2026 the hearing officer granted the state environment department's request, cancelled the September 21, 2026 hearing and set the hearing to begin March 22, 2027.

Heat stress7 sources · Checked Nov 18, 2026
Federal: EPA TSCAVacated

EPA's 2024 methylene chloride rule vacated by the Fifth Circuit

The Fifth Circuit vacated EPA's 2024 methylene chloride rule on September 15, 2026 and sent it back to EPA. EPA says the rule is no longer in effect, so its use prohibitions, workplace program and EPA exposure limits no longer apply.

Methylene chloride3 sources · Checked Nov 18, 2026
WashingtonUnder review

Washington begins indoor heat rulemaking for all industries

Washington opened an indoor heat rulemaking for all industries on August 18, 2026. Stakeholder meetings are running from November 3 to November 19, 2026, and comments are due by 5:00 p.m. on December 15, 2026.

Heat stress4 sources · Checked Nov 18, 2026
NevadaProposed

Nevada proposes workplace wildfire-smoke regulation (R070-26)

Nevada's Division of Industrial Relations (Nevada OSHA) proposed a wildfire smoke regulation that would require controls and voluntary N95 respirators at a PM2.5 AQI of 150 and stop outdoor critical tasks at an AQI of 500. A hearing was scheduled for July 22, 2026.

Wildfire smoke4 sources · Checked Nov 18, 2026
CaliforniaIn force

California SB 20 adds statutory artificial-stone silica duties

California SB 20 bans dry cutting and other dry methods for high-exposure silica trigger tasks and makes silicosis and silica-related lung cancer reportable as a serious illness. Fabrication shops must also file an annual training attestation with Cal/OSHA, starting July 1, 2026.

Artificial stone / silica2 sources · Checked Nov 18, 2026
Canada federal workplacesProposed

Federal proposal updates PPE and respirator provisions

A federal proposal published June 13, 2026 would update personal protective equipment rules in five Canada Labour Code regulations. It covers respirator provisions, a 19.5% oxygen-deficiency threshold across sector regulations and a requirement that PPE fitting by a qualified person take account of body type.

Personal protective equipment and respiratory protection3 sources · Checked Nov 18, 2026
British Columbia: WorkSafeBC jurisdictionFuture

British Columbia adds a combustible dust division from January 2027

British Columbia adds a combustible dust division to Part 6 of the OHS Regulation on January 4, 2027. Employers in WorkSafeBC jurisdiction who generate or handle dust will need to find out whether it is combustible and assess the combustion risk. Where that assessment finds a hazard, they will need a dust management program, worker training and specific controls.

Combustible dust2 sources · Checked Nov 11, 2026
British Columbia: WorkSafeBC jurisdictionIn force

British Columbia amends respirator face seal, fit test and seal check rules

British Columbia amended its respirator face seal, fit test and user seal check rules on November 6, 2026. The regulation now defines a tight-fitting respirator and says nothing may be permitted to interfere with the seal; earlier, standard references for respirators and safety headgear were updated on April 1, 2026.

Respiratory protection6 sources · Checked Nov 11, 2026
CaliforniaProposed

California proposes to lower the trichloroethylene PEL to 0.24 ppm

The California Occupational Safety and Health Standards Board proposes lowering the trichloroethylene PEL from 25 ppm to 0.24 ppm as an 8-hour TWA and withdrawing the 100 ppm short-term limit and 300 ppm ceiling. The hearing and comment deadline are December 17, 2026.

Trichloroethylene2 sources · Checked Nov 11, 2026
Federal: MSHAProposed

MSHA reopens proposal on non-permissible PAPRs in underground gassy mines

The U.S. Mine Safety and Health Administration reopened its 2025 proposal to allow powered air-purifying respirators without part 18 permissibility approval in specified underground areas of gassy mines. A virtual hearing was set for November 17, 2026 and comments are due December 8, 2026.

Respiratory protection1 sources · Checked Nov 11, 2026
British Columbia: WorkSafeBC jurisdictionIn force

British Columbia retains existing limits for new ACGIH recommendations

WorkSafeBC placed the June 2026 ACGIH recommendations on British Columbia's excluded-substances table effective September 3, 2026, after doing the same for the December 2025 batch on May 14, 2026. Existing provincial limits continue for all 18 entries until the Board decides.

Exposure-limit adoption process5 sources · Checked Nov 11, 2026
Federal: MSHAProposed

MSHA agenda entry for silica rule revisions, now proposed

The U.S. Mine Safety and Health Administration's August 2026 regulatory agenda listed planned revisions to the stayed silica rule, covering monitoring, respiratory protection and medical surveillance. MSHA issued that proposal with a Federal Register publication date of November 12, 2026.

Respirable crystalline silica3 sources · Checked Nov 11, 2026
WashingtonUnder review

Washington begins lead medical-removal rulemaking

Washington opened a preproposal inquiry on August 4, 2026 on lead medical-removal and return-to-work requirements. The state plans a second phase covering lead action levels, PELs and exposure assessment.

Lead / medical surveillance5 sources · Checked Nov 11, 2026
Federal: EPA TSCAIn force

Carbon tetrachloride WCPP and July 2026 deadline extensions

A U.S. EPA amendment effective July 28, 2026 extended selected carbon tetrachloride workplace inhalation-protection deadlines. Covered non-federal workplaces have initial monitoring due June 21, 2027 and specified protections due September 20, 2027; exposure-limit values and dermal-protection deadlines were unchanged.

CTC3 sources · Checked Nov 11, 2026
Federal: EPA TSCAIn force

Perchloroethylene WCPP and July 2026 deadline extensions

A U.S. EPA amendment effective July 28, 2026 extended selected perchloroethylene workplace inhalation-protection deadlines. Covered non-federal workplaces have staged dates in June, September and December 2027; the amendment did not change the exposure-limit values or dermal-protection deadlines.

PCE3 sources · Checked Nov 11, 2026
Multiple states: Washington, Oregon, Michigan, Minnesota, Nevada, CaliforniaVaries by jurisdiction

State-plan adoption of the 2024 federal Hazard Communication update

Washington, Oregon, Michigan, Minnesota and Nevada have adopted the 2024 federal Hazard Communication update. Washington's rule still uses a July 20, 2026 substance date, which has passed, and Oregon set later dates running to June 1, 2028.

Hazard communication / SDS10 sources · Checked Nov 11, 2026
OntarioIn force

Ontario recognizes CSA-approved respirators in three exposure regulations

Ontario amendments effective July 1, 2026 expressly recognize CSA-approved respirators in three exposure regulations and add Canadian particulate-filter identifiers to specified asbestos provisions. The changes concern respirator approval and filter references within each regulation's existing scope.

Respiratory protection and asbestos controls3 sources · Checked Nov 11, 2026
British Columbia: WorkSafeBC jurisdictionUnder review

British Columbia consults on a lower benzene limit

WorkSafeBC consulted on lowering British Columbia's benzene limit to 0.2 ppm as an 8-hour average and withdrawing the 15-minute limit. The consultation closed July 31, 2026. WorkSafeBC has since paused its consultation work generally because of the provincial election.

Benzene5 sources · Checked Nov 11, 2026
British Columbia: Mines Act workplaces (Health, Safety and Reclamation Code)In force

British Columbia mines code changes extended-shift limit adjustment

British Columbia's mines code changed how exposure limits are adjusted for shifts longer than 8 hours, effective June 22, 2026. The silica limit stays at 0.05 mg/m³ respirable and diesel particulate at 0.1 mg/m³ as elemental carbon, but silica is now adjusted by weekly hours, which gives a looser adjusted limit than the old formula on typical long-shift rotations.

Extended-shift exposure adjustment, silica and diesel particulate3 sources · Checked Nov 11, 2026
Federal: OSHAIn force

OSHA extends four Hazard Communication compliance dates

A U.S. OSHA amendment effective January 15, 2026 extended four Hazard Communication compliance dates by four months. Employer updates for substance labels, programs and training apply from November 20, 2026, and mixture deadlines follow in November 2027 and May 2028.

Hazard communication / SDS2 sources · Checked Nov 11, 2026
Federal: EPA TSCAPartly in force

TCE: use-specific phaseouts and partial postponement

U.S. EPA trichloroethylene requirements have use-specific phaseouts and selective postponements, including a May 18, 2026 postponement of conditions on section 6(g) exemptions during judicial review. An October 14, 2026 proposal would move the December 18, 2026 prohibition date for listed processing uses and wastewater disposal to December 31, 2027.

Trichloroethylene5 sources · Checked Nov 11, 2026
Federal: MSHAStayed

MSHA silica rule: compliance deadlines stayed

The U.S. Mine Safety and Health Administration finalized new silica protections in 2024, but the compliance deadlines remain stayed. MSHA's November 2026 proposal restates the stay and would revise sampling, respiratory protection and medical surveillance while keeping the 50 µg/m³ PEL and 25 µg/m³ action level.

Respirable crystalline silica4 sources · Checked Nov 11, 2026
QuebecIn force

Quebec updates Schedule I with staged commencement

Quebec's Decree 280-2024 amended RSST Schedule I and respiratory-protection certification requirements, with general provisions from March 14, 2024 and specified substance provisions from March 1, 2026. Decree 1305-2026 then changed the Schedule I title and notes wording and the CSA Z94.4 respirator reference from September 10, 2026, without changing any values.

Air-contaminant limits, notations and respiratory protection4 sources · Checked Nov 11, 2026
Canada federal workplacesFuture

Federal hazardous-substance rules scheduled for January 2027

Canada's adopted SOR/2026-10 amendments introduce hazardous-substance and industrial-hygiene duties for federally regulated workplaces, generally from January 30, 2027. Changes include inventories, record retention and sampling duties, with different requirements across the affected sector regulations.

Exposure assessment, records, radon, thermal stress and nanomaterials3 sources · Checked Nov 11, 2026
CaliforniaIn force

California lowers lead exposure limits

California amended its general-industry and construction lead standards effective January 1, 2025, generally lowering the eight-hour permissible exposure limit to 10 µg/m³ and action level to 2 µg/m³. Some provisions have later dates, and construction abrasive blasting has a temporary limit exception through the start of 2030.

Lead4 sources · Checked Nov 11, 2026
Canada federal supplier rulesIn force

WHMIS amended supplier requirements complete transition

Canada's transition to amended Hazardous Products Regulations ended December 14, 2025. Regulated suppliers must meet the amended classification, safety data sheet and label requirements; Health Canada says it will focus on compliance promotion until November 19, 2027 and then move to risk-based enforcement.

Hazard communication and SDS3 sources · Checked Nov 11, 2026
ManitobaPartly in force

Manitoba stages asbestos certification and registration duties

Manitoba's M.R. 108/2025 replaced asbestos provisions from registration on December 4, 2025, including inventory, record and notification duties. Specified certification, business-registration and related duties begin June 1, 2027.

Asbestos management2 sources · Checked Nov 11, 2026
British Columbia: WorkSafeBC jurisdictionIn force

British Columbia adopts selected 2021 to 2024 recommendations

British Columbia adopted selected exposure-limit and substance-definition changes effective June 20, 2025 within WorkSafeBC jurisdiction. The decision covers antimony trioxide, solvents, mica and other listed substances; benzene was left out and its existing limits were retained.

Solvents and chemical exposure limits3 sources · Checked Nov 11, 2026
WashingtonIn force

Washington aligns wildfire-smoke AQI references

Washington updated wildfire-smoke AQI references effective May 16, 2025 following EPA's revised AQI mapping. The change aligned the displayed AQI values while retaining the underlying PM2.5 concentration-based requirements.

Washington aligns wildfire-smoke AQI references2 sources · Checked Nov 11, 2026
NevadaIn force

Nevada heat-illness regulation and 2025 enforcement start

Nevada's heat-illness regulation was filed November 15, 2024, and full enforcement began April 29, 2025. It establishes heat-hazard analysis and related procedures, training and response duties for covered employers.

Nevada heat-illness regulation and 2025 enforcement start2 sources · Checked Nov 11, 2026
CaliforniaIn force

California makes enhanced silica protections permanent

California's enhanced general-industry silica protections became permanent on February 5, 2025. The amendments added protections for specified high-exposure tasks, including monitoring and respiratory protection, while retaining the existing 50 µg/m³ permissible exposure limit.

Respirable crystalline silica2 sources · Checked Nov 11, 2026
British Columbia: WorkSafeBC jurisdictionIn force

British Columbia adopts an inhalable fentanyl limit

British Columbia adopted an eight-hour limit of 0.0001 mg/m³ for inhalable fentanyl and fentanyl citrate, expressed as fentanyl, effective January 29, 2025. WorkSafeBC withheld the recommended short-term limit because of sampling issues.

Fentanyl2 sources · Checked Nov 11, 2026
New BrunswickIn force

New Brunswick begins full enforcement of amended rules

WorkSafeNB began full enforcement of the General Regulation 91-191 amendments on January 9, 2025. The checked regulation uses the 2016 ACGIH edition for its exposure-limit definition, subject to explicit exceptions.

Exposure controls and enforcement3 sources · Checked Nov 11, 2026
British Columbia: WorkSafeBC jurisdictionIn force

British Columbia styrene limits take effect

British Columbia removed styrene from WorkSafeBC's excluded-substances table on January 8, 2025. The resulting limits are a 10 ppm eight-hour time-weighted average and a 20 ppm short-term exposure limit within the applicable WorkSafeBC regime.

Styrene2 sources · Checked Nov 11, 2026
MarylandIn force

Maryland adopts indoor and outdoor heat protections

Maryland's indoor and outdoor heat-protection regulation took effect September 30, 2024. Covered work at a heat index of 80°F or above requires heat-stress protections, with additional measures under high-heat conditions.

Heat stress2 sources · Checked Nov 11, 2026
Federal: OSHAProposed

OSHA federal heat injury and illness prevention proposal remains pending

U.S. OSHA's 2024 proposal for a federal heat injury and illness prevention standard for indoor and outdoor work is still pending. It would use a heat index of 80 °F as the initial trigger and 90 °F as the high heat trigger, with WBGT alternatives.

Heat stress3 sources · Checked Nov 11, 2026
Federal: EPA TSCAProposed

1-bromopropane: proposed ECEL and use restrictions

U.S. EPA proposed use restrictions and workplace protections for 1-bromopropane in 2024, including an eight-hour exposure limit of 0.05 ppm for covered continuing uses. No final rule or binding compliance date was verified.

1-Bromopropane2 sources · Checked Nov 11, 2026
CaliforniaIn force

California indoor heat standard takes effect

California's indoor heat standard took effect July 23, 2024 for most indoor workplaces. Requirements generally begin at 82°F, with additional assessment and control triggers at 87°F and under specified 82°F conditions.

Heat stress2 sources · Checked Nov 11, 2026
Federal: OSHAIn force

OSHA updates Hazard Communication to GHS Revision 7

The U.S. Occupational Safety and Health Administration updated its Hazard Communication Standard effective July 19, 2024, principally aligning it with GHS Revision 7. Changes cover classification, labels and safety data sheets; a separate 2026 amendment extended the phased compliance dates.

Hazard communication / SDS2 sources · Checked Nov 11, 2026
British Columbia: WorkSafeBC jurisdictionIn force

British Columbia adopts selected chemical exposure limits

British Columbia changed selected exposure limits and substance definitions within WorkSafeBC jurisdiction on July 10, 2024. The changes include selected metals and other substances; the respirable manganese limit was expressly unchanged.

Chemical exposure limits2 sources · Checked Nov 11, 2026
Federal: EPA TSCAProposed

NMP: proposed workplace and dermal exposure controls

U.S. EPA proposed restrictions and workplace protections for N-methylpyrrolidone in 2024, with an emphasis on preventing skin contact. The checked sources still describe a proposal, and no final rule or binding compliance date was verified.

N-Methylpyrrolidone2 sources · Checked Nov 11, 2026
WashingtonIn force

Washington permanent wildfire-smoke rules commence

Washington's permanent workplace wildfire-smoke protections took effect January 15, 2024. Covered employers must follow the smoke-protection requirements under WAC 296-820 or the applicable agricultural provisions; AQI references were updated separately in 2025.

Washington permanent wildfire-smoke rules commence2 sources · Checked Nov 11, 2026
AlbertaUnder review

Alberta consults on benzene and diesel particulate limits

Alberta's 2026 occupational exposure-limit review proposes changes involving benzene, diesel particulate matter and exposure assessment. Feedback remains under review in the checked source, with no adoption or binding commencement date established.

OEL review and sampling rules2 sources · Checked Nov 11, 2026
MinnesotaUnder review

Minnesota develops revised lead standards

Minnesota is developing revised lead standards through a pre-rulemaking feedback process. The checked material does not establish adopted numerical limits or a binding implementation date.

Minnesota develops revised lead standards2 sources · Checked Nov 11, 2026
Nova ScotiaIn force

Nova Scotia confirms automatic adoption of 2024 limits

Nova Scotia's Safety Branch identified 2024 exposure-limit changes under the province's latest-version incorporation, including benzene, epichlorohydrin and fentanyl. The regulation allows a limited transition using the required or immediately previous edition; exact adoption dates were not established here.

Chemical exposure limits2 sources · Checked Nov 11, 2026
Australia: national list; mining applicability variesFuture

New national WEL entry for diesel particulate matter

Australia's future workplace exposure limit list adds diesel particulate matter at 0.01 mg/m³ measured as respirable elemental carbon. Application is scheduled from December 1, 2026 in adopting regimes and depends on the relevant jurisdiction and sector law.

Diesel particulate matter2 sources · Checked Sep 17, 2026
Australian Capital TerritoryIn force

ACT adopts lower aluminium welding fume WES on 9 September 2026

The Australian Capital Territory adopted the 1 mg/m³ eight-hour aluminium welding-fume standard on September 9, 2026. Its local commencement followed the November 2025 national-list revision.

Aluminium welding fumes2 sources · Checked Sep 17, 2026
Australia: national guidanceGuidance

New air-monitoring guides published for the WEL transition

Safe Work Australia published employer and technical air-monitoring guides in July 2026 for the workplace exposure limit transition. The paired guides replace the earlier interpretation guidance from December 1, 2026.

IH monitoring and interpretation2 sources · Checked Sep 17, 2026
Australia: national WEL decisionNot adopted

Nine proposed limit reductions will not proceed at the December 2026 transition

Australia's June 2026 decision retains existing limits for nine chemicals at the December 1, 2026 transition, including benzene and respirable crystalline silica. The proposed reductions for those substances will not proceed at that transition; further work remains pending.

RCS and eight other chemicals3 sources · Checked Sep 17, 2026
International guidance; local legal adoption not establishedVoluntary guidance

ISO/PAS 45007 guidance on climate-related workplace risks

ISO/PAS 45007:2026 provides voluntary guidance on occupational health and safety risks associated with climate change and adaptation or mitigation work. Its publication establishes no mandatory numerical exposure limit or statutory commencement date.

IH standards and climate-related workplace hazards2 sources · Checked Sep 17, 2026
Australia: national list; local commencement variesVaries by jurisdiction

National aluminium welding fume WES reduced to 1 mg/m3

Australia's national list reduced the eight-hour aluminium welding-fume standard to 1 mg/m³ on November 17, 2025. Local adoption dates vary; the Australian Capital Territory's separate commencement is recorded in the related finding.

Aluminium welding fumes3 sources · Checked Sep 17, 2026
Australia: national model guidanceModel code

New model silica Code of Practice and November clarifications

Safe Work Australia published a model silica Code of Practice in August 2025 and clarified professional titles and reporting in November. It provides a reference for silica assessment and controls; local approval of this edition requires confirmation.

Silica controls and monitoring2 sources · Checked Sep 17, 2026
Commonwealth: customsIn force

Engineered stone import prohibition

Australia's federal import prohibition for engineered-stone benchtops, panels and slabs began January 1, 2025. It complements the domestic workplace prohibition and permits imports only where a specified written permission, confirmation or exemption applies.

Engineered stone imports2 sources · Checked Sep 17, 2026
Commonwealth and all Australian states and territoriesIn force

Domestic engineered stone prohibition

Australia's domestic prohibition on defined engineered-stone benchtops, panels and slabs began July 1, 2024, covering manufacture, supply, processing and installation. Limited exceptions and controls apply to permitted legacy work; available transitional-contract periods ended in 2024.

Engineered stone2 sources · Checked Sep 17, 2026
New South WalesIn force

NSW requires reporting high-risk silica WES exceedances

From September 1, 2024, New South Wales requires reporting of workplace exposure-standard exceedances associated with high-risk crystalline-silica-substance processing. Notification and the air-monitoring report are due as soon as reasonably practicable, within 14 days of receiving results; monitoring reports must be retained for 30 years.

RCS air monitoring2 sources · Checked Sep 17, 2026
Australia: model framework; local adoptions separately evidencedVaries by jurisdiction

Stronger model regulation of crystalline silica processing

Australia's stronger model crystalline-silica processing provisions have a September 1, 2024 commencement framework, with local variations. They cover materials containing at least 1% crystalline silica by weight and add controls and high-risk processing duties.

Crystalline silica substances7 sources · Checked Sep 17, 2026
Western Australia: general workplacesIn force

WA silica processing changes apply under General Regulations, excluding mine sites

Western Australia commenced enhanced crystalline-silica processing requirements under its General Regulations on September 1, 2024. The changes include reporting relevant high-risk processing exceedances and expressly exclude mine sites from this General Regulations package.

Crystalline silica substances2 sources · Checked Sep 17, 2026
Australian Capital TerritoryIn force

ACT silica Code of Practice takes effect

The Australian Capital Territory's approved silica Code of Practice took effect July 1, 2024. It provides practical guidance under ACT WHS law for silica risks from engineered stone and other materials.

Silica risk management2 sources · Checked Sep 17, 2026
Australia: national policy; local WHS/OHS implementationFuture

WES list scheduled to become WEL list on 1 December 2026

Australia's revised workplace exposure limit list is scheduled for the December 1, 2026 transition, with current workplace exposure standards continuing through November 30. Legal application depends on the adopting jurisdiction and relevant sector legislation.

Exposure limit framework2 sources · Checked Sep 17, 2026
International; local adoption or contractual applicability must be checkedVoluntary standard

ISO 45001 climate amendment published

The 2024 amendment to international standard ISO 45001 adds consideration of climate-change relevance and related interested-party requirements to the occupational health and safety management-system context. Publication does not establish a universal statutory compliance date.

IH standards2 sources · Checked Sep 17, 2026
Australia: national list; local commencement variesVaries by jurisdiction

National welding fume WES reduced from 5 to 1 mg/m3

Australia's national list reduced the eight-hour workplace exposure standard for welding fumes not otherwise classified from 5 to 1 mg/m³ on January 18, 2024. Substance-specific component limits also apply, and local or sector commencement requires separate confirmation.

Welding fumes2 sources · Checked Sep 17, 2026
International; local adoption or contractual applicability must be checkedBaseline

EN 689 current edition remains a baseline reference

BSI lists BS EN 689:2018, incorporating the 2019 corrigendum, as the current exposure-assessment reference in the checked publisher metadata. No new 2024 to 2026 edition was verified; this entry records the current baseline.

IH standards2 sources · Checked Sep 17, 2026
International; local adoption or contractual applicability must be checkedDraft

ISO 45001 revision in development

ISO is developing a successor to international standard ISO 45001, with the next edition planned for 2027. The checked information does not establish final replacement requirements or a transition deadline.

IH standards2 sources · Checked Sep 17, 2026
Queensland: mines and quarries under MQSH legislationBaseline

Queensland mining retains separate welding, silica and diesel treatment

Queensland's checked mining Schedule 5 treats welding fumes, respirable crystalline silica and diesel particulate matter separately from its general incorporation of the Safe Work Australia list. This entry records that sector-specific baseline without asserting a new commencement date.

Mining exposure limits2 sources · Checked Sep 17, 2026
VictoriaBaseline

Victoria distinguishes mandatory RCS WES from precautionary recommendation

Victoria's checked guidance distinguishes the mandatory 0.05 mg/m³ respirable crystalline silica workplace exposure standard from a precautionary recommendation to remain below 0.02 mg/m³. This entry explains the baseline and does not establish a new 2025 reduction.

RCS exposure interpretation3 sources · Checked Sep 17, 2026

Each record includes the original sources, relevant dates and unresolved questions. See coverage and methodology for the limits of this resource.